Hinkley-lighting YORK 1845 Bedienungsanleitung PDF herunterladen

assembly instructions

Item No. 1840 / 1844 / 1845

1. Find a clear area in which you can work.

2. Unpack xture and glass from carton.

3. Carefully review instructions prior to assembly.

1. To install glass panels (2), slip them up through the open bottom of the cage (1). The center

stem that is attached to the socket cluster assembly (not shown) is on a swivel and can be moved

to aid in installing the glass - see Drawing 1.

2. Slip bottom of glass panels (2) into channel (3) in bottom of cage (1) tip top of panel into

position, and bend over clips (4) to secure glass in cage. Repeat procedure for remaining panels of

glass.

*** The construction of this xture will be accomplished by rst installing the glass, attaching

mounting hardware to the junction box, making all necessary electrical connections, attaching

the xture to the wall.

start here

1844

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Drawing 1 - Glass Installation

Make electrical connections from supply wire to xture lead wires. Refer to instruction sheet (I.S. 18)

and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to

continue installation of this xture.

6.1.12

Drawing 2 - Fixture Mounting

1. Prepare threaded tube (C) by threading on hex nut (D) approximately 1/2”.

2. Thread tube (C) in mounting strap (A), approximately 1/4 “ - see Drawing 2.

3. Attach mounting strap (A) to junction box (J) using two screws (B) provided.

4. It will be necessary to adjust threaded tube (C). This is done by slippiing the mounting hole (E)

over threaded tube (C) and holding the xture against the wall. Adjust threaded tube (C) until

there is approximately 3/8” of thread showing inside the xture. Remove xture from wall and

tighten hex nut (D) against mounting bracket (A) to secure threaded tube (C) in place.

1. To mount xture, slip center hole of backplate (E) over threaded tube (C) and hold xture in

position - see Drawing 1.

2. Thread decorative nut (F) onto end of threaded tube (C) and tighten to secure xture.

3. Slip reector (G) onto threaded tube (C).

4. To complete assembly thread barrel knob (H) onto end of threaded tube (C) and tighten.

5. your xture can now be lamped accordingly.

1840

1845

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2 3

Inhaltsverzeichnis

Seite 1 - Item No. 1840 / 1844 / 1845

assembly instructionsItem No. 1840 / 1844 / 18451. Find a clear area in which you can work.2. Unpack xture and glass from carton.3. Carefully review

Seite 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Seite 3 - Caulking Instruction____

I.S.200 Caulking Instruction____start here---Drawing

Verwandte Modelle: YORK 1844 | YORK 1840 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Hinkley-lighting YORK 1845 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Hinkley-lighting YORK 1845 herunter. Hinkley Lighting YORK 1845 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: YORK 1844 | YORK 1840 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Hinkley-lighting YORK 1845