Hinkley-lighting MONTAUK 1205 Bedienungsanleitung PDF herunterladen



assembly instructions

Family: Montauk Item No. 1205

1. Find a clear area in which you can work.

2. Unpack ﬁxture and glass from carton.

3. Carefully review instructions prior to assembly.

*** The construction of this ﬁxture will be accomplished by ﬁrst mounting the

mounting strap to the junction box, making all necessary electrical connections,

mounting the ﬁxture to the wall, and then lamping the ﬁxture .

start here

1205

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)

AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING

INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED

ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.



Drawing 2 - Fixture Assembly

Make electrical connections from supply wire to ﬁxture lead wires. Refer to instruction

sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

Then refer back to this sheet to continue installation of this ﬁxture.

Drawing 1 - Fixture Mounting

B C D

E F

back plate

1. Prepare mounting strap (A) by threading the two 1 1/4” long mounting screws (B)

into the back of the mounting strap (A) - see Drawing 1.

• Be sure the holes into which the screws are threaded match the spacing of holes (D)

in the backplate (E).

2. Attach mounting strap (A) to junction box (J) using two 1” screws (C).

1. To mount ﬁxture, slip the two mounting screws (B) through the two mounting holes

(D) in the backplate (E) - see Drawing 1 .

2. While holding ﬁxture in place, thread the two ball knobs (F) on to the end of the

mounting screws (B) , and tighten.

1.01.12

Drawing 2 - Glass Installation

1. To install glass, slip glass panel (1) into the cage assembly (2) - see

Drawing 2 .

2. Slip top of glass panel (1) under top glass clips (3).

3. Slip bottom of glass panel (1) into the bottom of the cage assembly (2).

4. Bend lower glass clips (4) up to retain glass panels (1).

5. Repeat steps 1-4 for remaining panels.

6. Set cage aside after installing glass, this will be attached to xture after main body

is mounted to the wall.

1. After mounting main xture body to wall xture can be lamped accordingly.

2. Attached cage assembly with glass to xture by slipping studs (6) of main xture

body into holes (7) of cage assembly.

3. Thread ball knobs (8) onto end of studs and tighten to secure cage assembly to

xture body. Fixture is complete.

H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

1 2 3

Inhaltsverzeichnis

Seite 1 - Drawing 1 - Fixture Mounting

assembly instructionsFamily: Montauk Item No. 1205 1. Find a clear area in which you can work.2. Unpack ﬁxture and glass from carton.3. Carefull

Seite 2

I.S. 18 wiring grounding instructionsSAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPL

Seite 3 - Drawing 1

I.S.200 Caulking Instruction____start here---Drawing

Kommentare zu diesen Handbüchern

Keine Kommentare

Hinkley-lighting MONTAUK 1205 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Hinkley-lighting MONTAUK 1205 herunter. Hinkley Lighting MONTAUK 1205 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Hinkley-lighting MONTAUK 1205